Search Results for ‘size’

Can anyone just confirm the standard drive chain size for my 2000 GS so I know I am looking for the right one, I have standard chain and sprockets, so Is this right size 520 X 112 ? I know you should replace the sprockets as well but they are not bad at all and will certainly see this year...

Hiya Folks I was wondering if someone can help me out... I am about to replace the ignition barrell and lock mechanism.. I believe it is held in place by 2 bolts.. that are the sheer type... so when I remove them (by careful means I am sure) and need to replace them, what do I use? I had...

Hello all - I'm going round the bend trying to track down some 5mm bolts, domed head with hex key; the problem is I need 75mm long, and that's where it falls down. 20-40mm no problem but any longer and I just get looked at like I'm insane. Even the mighty electronical interweb has failed to...

i have to replace my rear wheel bearings; so, what size bearing do i need and does anybody know a website i can get them from. i found some at motorworks but i only want a rear and this kit is f&r. http://www.motorworks.co.uk/bmw/products/product.php?f=b&bke=bmw&q=WHA45335&x=0&y=0 thanks will

What is the best size Airhawk for the 650gs? The seat measurements suggest a small. But which is best in reality? Val.

Hi, Can someone shed some light on the correct size for the hub nut on a CS please? Have measured it with a vernier (55mm) but have heard its a 56mm? Local bike shop wrecked the plastic adaptor that came with the biketrying to undo the nut!!

Anyone had trouble trying to remove the rear wheel nut on a cs? Local bike shop tried using the plastic adaptor but wouldn't budge. Is this common? Going have to buy a 55mm socket and carry it around in case of a puncture!

Howdo could someone with a Funduro tell me the diameter of the handlebar where it is clamped to the top yoke. Im after some for my Strad and they measure 22.5mm or 7/8" if my conversions are right. Thanks Dazco :not worthy:

I bought a used 05 650gs a couple of weeks ago and am loving it. I haven't had chance to go for a proper ride yet, but have used the bike on my daily commute. I park my bike down the side of my flat in the alley which leads round the back of the place, there's a gap that is almost custom made...

Hi What is the largest size I can fit ? I need a new rear Anakee as the front had just been replaced when I bought it 1000 miles ago. Think I should replace the rear now. This is purely from an aesthetics point of view - sad I know, but the tyre thats on there now looks too small in comparison...

Hi all - riding back from the New Forest today, I noticed my ignition has sunk into the yoke. On closer inspection, it looks like the 2 bolts that fix the lock and cable guide in place have gone - must have vibrated loose I guess. I can't find the bolt size in my Clymer or on the Chain Gang...

Hi from Spain. I want to purchase a pair of boots using internet but always the same problem arises which is my correct size to order. So I beg your help, use some users here have the same foot length I have 26.3 centimetres (bare feet). So for this ones which is the size(US UK europen) of your...

Which size socket for engine oil drain plug? Didn't have one to fit.

Hello, I have taken both wheels in for rim replacement. They had gone really naf !! They have told me they cannot get a 3 inch wide rim for the rear. It will have to be 3.5 inch. Any comments ?

My Dakar runs smoothly with its standard 16 tooth front sproket fitted, but when I change it for a 13 tooth sprocket (for off road use) I get a surging between 5,000 and 7,000 revs which makes motorway riding a real pain (Motorway is used to get to the greenlanes). Anyone had a similar problem...