BMW F650 Forums banner

Discussions Showcase Albums Media Media Comments Tags

1-20 of 23 Results
  1. F650 Single Discussion
    Can anyone tell me which way round the drive sprocket (Engine end) should go, With the raised lip facing the engine or with it facing out. It seems daft but I cant remember which way round it should go. I blame the wife for yelling at me to come in for lunch. Many thanks. :confused: :think:
  2. F650 Single Discussion
    I have a 2004 F650CS. At the rear end of the swing arm, either side of the adjuster screw are two pinch bolts. These seem to periodically work loose. The first time I noticed this was after a 2500 mile trip abroad, when one bolt fell out. The bike had it's 12000 mile service prior to the trip...
  3. F650 Single Discussion
    Hi Well I am down to the main shaft drive sprocket... The Clymer Manual says to put a 'soft washer' between the main sprocket and the sprocket of the clutch basket.... then take the nut off... Agghhhh.. is this the only way? Really worried about damaging the main sprocket or clutch...
  4. F650 Single Discussion
    Just had the forks off my fubduro 96 to fit a pair of gaiters, when refitting front wheel/speedo drive the Clymer states line up the notches of speedo drive to notches in the wheel hub. The book is a Vauge on how to do this and does not show any diagrams, I've fitted it all back how I think but...
  5. F650 Single Discussion
    Can anyone just confirm the standard drive chain size for my 2000 GS so I know I am looking for the right one, I have standard chain and sprockets, so Is this right size 520 X 112 ? I know you should replace the sprockets as well but they are not bad at all and will certainly see this year...
  6. F650 Single Discussion
    Any advise from the CS owners out there? In the last week my bike has got coverd in brown dirt, so much so my wife thought my exaust had gone rusty in the road salt, until I wiped it off with my hand, so I'm going to clean it tomorrow. Anyway, what I was wondering was, is there anything I...
  7. F650 Single Discussion
    hello is it possible to buy a speedo plastic drive gear or will i have to buy the complete unit.and where can i find a picture looking into the top of the drive to see how it looks without cable im trying to remove a snapped cable many thanks russell.
  8. F650 Single Discussion
    Hey again Following on from my last topic, it seems the nut that holds on the front sprocket has disappeared. I have checked the Motobins and Wemoto websites but cannot find one. Any idea where I can find one ??? Cheers :howdy:
  9. F650 Single Discussion
    I have a 2004 F650CS which has done 12000 miles and has a hole in the belt drive. Looks like a stone has picked up on the pulley wheel and punctured a small hole in the belt. It's not a distinct hole, the material has been pushed up and punctured. It's about 2mm wide and fairly central on the...
  10. F650 Single Discussion
    Guys, working on an F650CS, 2003, belt drive. How is the belt tension adjusted ? Though it's already a low seat model, we need to lower it even more for a very short rider. I'm thinking this means longer links between the triangular pivot at the bottom of the shock and the swinging arm. Anyone...
  11. F650 Single Discussion
    my '05 dakar has always had a bit of what i assumed was the well known surging problem. but recently it seems to be getting worse (unless it's my imagination) and i just thought i'd check that it is what i thought it was. symptoms are lumpy power delivery when at steady or slowly changing...
  12. F650 Single Discussion
    I think mine is totally worn. I've just made my way back from northampton after spending the weekend at the Renault World Series at silverstone, on the way there my chain was much too loose so after 60 miles had to adjust it and once I got back it now seams much too tight and the drive chain...
  13. F650 Single Discussion
    Not wanting to buy crap or over the odds - What is a good make of drive chain and sprockets, and which supplier has the keenest prices?
  14. Chatter
    What is it about other BMW owners and this fixation with Shaft drive ? If its not shaft drive its not a proper BMW they say. We have two shaft drive BMW's in our household an 1100GS (90,000miles) and a K1200LT(40,000). The GS is now on its 3rd Final Drive Main Bearing and the LT has just failed...
  15. F650 Single Discussion
    Can anybody recommend a 1/2 drive torque wrench for working on the CS my old one is too rusty to be serviceable. :oops: Cheers John
  16. F650 Single Discussion
    I know this may sound ridiculus, but is it possible to change a chain and sprocket kit for a belt drive.
  17. F650 Single Discussion
    I heard a rumour that BMW are working on turning the F650 into a shaft drive bike. This was not down the pub at 2 am, but at a bike show. I know there is always a lot of talk, but look what happened. They talked of a 1200 GS, a 1200GS ADV, an HP2, an HP1, an F800, a more off-road orientated...
  18. F650 Single Discussion
    Hello, I have been trying to pull together a tool kit and via the FAQ site and previous posts, it seems that most can be done using a 1/4" drive, but that a larger is necessary for wheel nuts and the sump plug (plus a couple of the 10mm hexes). My question is: for nuts such as 24mm, is a 3/8"...
  19. F650 Single Discussion
    1977 Bultaco Metralla GTS 250 - 6 speed
  20. F650 Single Discussion
    I could do with some help on checking and if necessary, adjusting the belt on the CS. Could anyone send me a reply in English that a girly can understand and use? :dance:
1-20 of 23 Results