BMW F650 Forums banner
bolts
1-14 of 15 Results
  1. Bike Tech / Kit / Reviews
    Hi has anyone used these bolts or got any comments on them. Just wondering if they are any good seem a bit cheap to me thank Paul...
  2. Sale - Wanted - Swap (UK Only)
    Hi there are a set of four 04 F650 GS OE BMW handlebar bolts here http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=290479283484&ssPageName=STRK:MESELX:IT They are stainless steel and have a threaded hole in the top for mounting stuff to, originally it was the hazard light switch mounting...
  3. F650 Single Discussion
    ive misplaced a few of the allen bolts for putting in the side panel/tank fairing. are these m4/m5 if so what lenght is best please? thanks
  4. F650 Single Discussion
    Well, I've been working hard on my F650 - new steering head bearings, new fork seals - I've been doing well, as I normally break something along the way... But, I've just sheared one of the 4 safety nuts that hold the front wheel axle in place... the little weedy 10mm fellas... It sheared...
  5. F650 Single Discussion
    Hello all - I'm going round the bend trying to track down some 5mm bolts, domed head with hex key; the problem is I need 75mm long, and that's where it falls down. 20-40mm no problem but any longer and I just get looked at like I'm insane. Even the mighty electronical interweb has failed to...
  6. F650 Single Discussion
    While you're all out there checking your nuts and bolts (I saw the I'm very lucky post ), I have used stagonset.co.uk for stainless bolts, washers, hoseclips etc etc. Quite good prices, next day delivery. I guess they dont have everything you may need, but motorworks runs out sometimes I have found.
  7. F650 Single Discussion
    Owner of a 2007 F650GS - gets model out of the way. I want to whip the pads out and have a check at their condition - I get paranoid about the condition of my brakes - or perhaps I just ride too close to the car in front! The chaingang FAQ suggests that it's best to take out the front wheel -...
  8. F650 Single Discussion
    Another pls..............41nM yes or no? Thanks
  9. F650 Single Discussion
    Just put the TT low mudguard on and can't remember the torque settings for the brace bolts..............set it @ 26nM Yes or No?
  10. F650 Single Discussion
    Hi all, Does anyone know the correct tension for the rear sprocket nut and bolt. Themarshall01
  11. F650 Single Discussion
    Hi anyone know where I can source some new Handle bar Bolts? Mine are rusty so I'd like to replace them. Cheers
  12. F650 Single Discussion
    Does anyone know if there is a suitable tool that fits the screw/bolts on the '04 GS. I have got hold of a replacement horn (half of the double on the 1200) and need to access the housing. I am having trouble dropping the front guard as the bolts are in a tight space & I cannot get leverage on...
  13. F650 Single Discussion
    Over the years the various nuts and bolts exposed to the elements have a very noticable coating of rust and look pretty ugly. Think its only surface rust so was wondering if anyone has any recommendations on cleaning up? Was thinking along the lines of soaking in something, washing off then...
  14. F650 Single Discussion
    Changing the rear disc on my son's 94 F650. Natuarlly three of the screws were seized. :-( I eventually got them out but they will need replacing with new ones. The service book says to refit using Loctite and do up to 12Nm. I'm not a big fan of Loctite but want to do the job right. Maybe...
1-14 of 15 Results
Top